AM FM RADIO TAPE TRAINER
IPC-24-B
SPECIFICATION:
Model IPC-24-B is a conventional super heterodyne type radio receiver, suitable for comprehensive training in Radio mechanic, the trainer represents a fully operational AM & FM Radio set and demonstrate principals and operating characteristics of AM Radio receiver, it is possible to simulate typical fault by means of dip switches. Test points are clearly arranged for use of measuring instruments. AM frequency 53 to 160 KHz, FM Frequency 88 to 108 MHz operate on 220 V 50 Hz.


AM RADIO TRAINER
IPC-22-B
SPECIFICATION:
Model IPC-22-B is a conventional super heterodyne type radio receiver, suitable for comprehensive training in Radio mechanic, the trainer represents a fully operational AM Radio set and demonstrate principals and operating characteristics of AM Radio receiver, it is possible to simulate typical fault by means of dip switches. Test points are clearly arranged for use of measuring instruments. AM frequency 540 to 1640 KHz, operate on 220 V 50Hz.


ANALOG / DIGITAL TRAINER
IPC-122-AD
SPECIFICATION:
  • DC FIXED & VARIABLE POWER SUPPLY
  • ±5 Volts @ 1.0A Variable 0±20 Volts @ 1.0A
  • Function Generator:
  • 1Hz to 100 KHz continuously variable over 5 decade ranges. Sine wave, square wave, triangle wave.
  • 3 state logic probe.
  • Seven segment display
  • Two single shot pulse generator, 80 µs.
  • 2 inch 8Ω, 1 w loud speaker.
  • Two logic switches ±5 V/0V with current limit.
  • 8 data switch +5V/0V.
  • Potentiometer 1K, 100K, 1M
  • Double size bread board.


ANALOG TRAINER MODEL
IPC-122-AD
SPECIFICATION:
DC FIXED & VARIABLE POWER SUPPLY ±5 Volts @ 1.0A ±12 Volts @ 1.0A Variable 0±20 Volts @ 1.0A
Function Generator:
  • 1Hz to 100 KHz continuously variable over 5 decade ranges. Sine wave, square wave, triangle wave.
  • Analog current meter 0 to 100µA..
  • Analog Volt meter 0 to 30VDC..
  • Variable Resistor 5K, 10K, 100K..
  • 2 ¼ inch 8Ω, 1 w loud speaker..
  • Input / output connectors, BNC and banana..
  • Double size bread board..
  • User Manual..
  • Connecting Leads. .
List of Experiments:
  • The Superposition Theorem
  • Capacitor in Voltage - divider networks
  • Operational Amplifier - The Inverting Amplifier
  • Operational Amplifier - The Non-inverting Amplifier
  • Operational - The Comparator
  • Operational Amplifier - The Summing Amplifier
  • The Common-Base Amplifier Structure
  • The Common-Emitter Amplifier Structure
  • The Common-Collector Amplifier Structure
  • The Op Amp Differentiator
  • The Op Amp Integrator
  • The RC Phase Shift Oscillator
  • The Astable Multivibrator- 555 Timer
  • The Schmitt Trigger
  • The Astable Multivibrator
  • The D/A Converter
  • The A/D Converter


BASIC DIGITAL LOGIC TRAINER MODEL
IPC - 180 - DL
SPECIFICATION:-
Operating Voltage 220-230 Volts 50Hz Board Size 10" x 12" Fixed in rugged carrying case.
Potentiometer: Variable Resistor 5K(B). Variable Resistor 10K(B). Variable Resistor 100K(B).
ON BOARD FACILITES
Fixed DC Output Power supply.DC +5 Volts 200mAmps.DC +12 Volts 200mAmps.DC -12 Volts 200mAmps.Double Size solder less Breadboard. Main ON / OFF Switch with light indicator.Logic Switches 8Nos.Lamp Monitor L.E.D 8Nos. Seven Segment Decoder display. Debounce Switches 2Nos. Pulse Catcher / Logic Probe.Clock Timer.Connecting Leads.User Manual.
The following types of experimental circuit can be connected and studied.Combinational logic circuit experiment.
           C. .Arithmetic circuit experiment.
1)DL circuit experiment 1) ALU experiment.
2) RTL circuit experiment 2) Serial adder experiment
3) DTL circuit experiment 3) Parallel adder experiment
4) TTL circuit characteristics experiment D. Memory experiment.
5)C-Mos circuit characteristics experiment 1) RAM experiment.
6) TTL -> C-Mos interface circuit experiment 2) ROM experiment.
7) C-Mos -> TTL interface circuit experiment 3) EPROM experiment.
8) Basic logic function E. A/D, D/A Conversion experiment.
9) Exclusive OR gate experiment 1) A/D conversion circuit experiment.
10)TTL,C-MOS half adder & full adder experiments 2) D/A conversion circuit experiment.
11)TTL,CMOS half subtract & full subtract experiments F. Logic circuit application experiment.
12) Open collector gate experiment 1) Digital Voltage meter experiment.
13) Open drain gate experiment 2) Advertising light experiment.
14) Encode and decode experiment 3) Digital capacitance meter experiment.
15) Multiplexer or de multiplexer 4) Electronic metronome meter experiment.
16) Comparator experiment 5) Music IC application experiment.
B. Sequential Logic Experiment. 6) Electronic stop watch experiment.
1) RS Flip flop experiment 7) Electronic dice experiment.
2) T Flip flop experiment 8) Frequency counter experiment.
3) JK Flip flop experiment 9) Electronic clock experiment.
4) Master/Slave JK Flip flop experiment G. Timing & Pulse generating circuit.
5) Edge-triggered JK Flip flop experiment 1) Pulse generating circuit experiment.
6) D Flip flop experiment
2) Non-re triggable monostable multivibrator.
7) Asynchronous binary counter experiment 3) Retriggable monostable multivibrator.
8) Synchronous binary counter experiment 4) Quartz crystal oscillator experiment.
9) BCD counter experiment 5) Schmitt trigger circuit experiment.
10) Up/ down counter experiment 6) 555 circuit experiment.
11) Divide by N circuit experiment
12) Serial in-serial out shift register experiment
13) Serial in-parallel out shift register experiment
14) Parallel in-serial out shift register experiment
15) Parallel in-parallel out shift register experiment
16) Left / right shift register experiment


BASIC ELECTRONICS TRAINER
IPC-102
SPECIFICATION:
  • Fixed DC Output +5Volts 200mAmps.
  • Fixed AC +5V through center tap transformer.
  • Variable DC output ±20Volts 200mAmps.Ripple less then 20mV.
  • Digital multimeter.
  • Speaker with 0.25 Watts amplifier.
  • Two Nos of relays
  • BNC type connectors for connecting instruments such as an oscilloscope, function generator, etc.
  • Clock Pulse 7Hz to 50Hz.
  • Lamp monitors five Nos.
  • Variable Resistor 5k, 10k, 100k
  • Double size bread board (350mm x 134mm x 8mm)
  • Operating voltage 220Volts 50Hz.
This trainer will covers the experiments for ELT-264.

-Diodes
  • Rectifier diodes
  • Zener Diodes
  • Diodes circuits
  • Photo diode relays
  • Super position & AC resistance
-Amplifiers
  • The CE amplifier.
  • Class A amplifier.
  • The class B push-pull amplifier
  • The silicon controlled rectifier.


COLOR T.V TRAINER MODEL
IPC-104-B
SPECIFICATION:
IPC-104-B is suitable for theoretical and practical study of color TV. The main PCB is mounted in the specially designed cabinet. The complete block diagram is distributed on panel. i.e. antenna cum tuner, IF amplifier cum detector, FM detector and audio output, Video amplifier, sync. Separator, Horizontal Oscillator, Vertical oscillator and vertical output, power supply. PAL decoder system. Infra red remote control receiver with hand held remote controller.
The provision is available to insert faults that commonly occur in various stages can be simulated individually or combined with each other, through the faults simulation panel.Channel system: 100 channels, Hyper Band Tuner, and 24 Hours Programmable TV ON /OFF. A/V In/Out, auto voltage regulator, convenient sleep timer, and remote control, high power Audio Output, 10 Watts, picture tube 14 inches. Operate on 220 V 50Hz.


DIGITAL ELECTRONICSTRAINER MODEL
IPC-185-AD
SPECIFICATION:
The IPC-185-AD Digital Electronics Trainer is a comprehensive and self contained system. It is an idea to learn or experience the basic features of digital & logic concepts with IPC-185-AD in a very short time. The whole system is consists of PCB designed with thirty different experimental modules. Onboard power supply of +5 Volts, timer clock, PUSH ON & PUSH OFF switches, LED display for clock pulse.
This trainer will perform the following practical.
- AND GATE OPERATION - SHIFT REGISTERS
- OR GATE OPERATION - 4 BIT COMPARATORS
- NAND GATE OPERATION - 4 BIT FULL ADDER
- XOR GATE OPERATION - MULTIPLEXER
- NOR GATE OPERATION - DEMULTIPLEXER
- INVERTER - MONOSTABLE
- TTL & CMOS LOGIC FAMILIES - 9 BIT PARTIY GENEARTOR
- TRI STATE BUFFER - BCD-DECIMAL DECODER
D FLIP FLOP - BCD-7 SEGMENT DECODER DRIVER
- JK FLIP FLOP - 7 SEGMENT LED DISPLAY
- R-S LATCHES - DECIMAL-BCD CODER
- BCD, BINARY, UP/DOWN COUNTER - BCD SELECTOR


PROGRAMMABLE LOGIC CONTROLLER TRAINER MODEL
IPC-24-16 (Digital)
SPECIFICATION:
This trainer covers the following topics: Relays vs. programmable logic controller, how PLC functions, ladder diagram, ladder logic applications, program basis, programming the PLC, Editing program mistakes, series & parallel logics, Timer circuits, Counters, Sequencer circuits, Master control, Start/Reset, Shift register, Special scan timer logic circuit, High speed counter, Audio cassette program loading & down loading.
TECHNICAL SPECIFICATION: Power 230V 50Hz Approx.35w DC Supplies +5V,.08A A.10 mV Ripple, 3.5 regulation, with no load on ±15VAC, 0.8A each load on +5supply (1A each at ±10V), LED power supply indicator (3), 5VAC, 0.1A (20 primary 230V 50H, power supplies are short circuit protected, power supply terminal for measuring voltages. 15 pin Winchester socket provided for connection ,accessory panel bas. PLC SPECIFICATION: Operating temperature: 0-60 degree celcius (32-140F) available user power (DC) 24Volts @ 0.1A max. battery life:-2 to 5 years, Memory size 16-bit words,700 words COMS EPROM. Scan Rate:12ms for 250 words.40 ms. For 700 words I/O points, 8 inputs, 6 outputs.


FUNCTION GENERATOR MODEL
IPC-FG-219
SPECIFICATION:
Description:- The unit is versatile and compact Function Generator capable of generating high quality sine triangle and square waveforms of high stability and accuracy.The sine and triangle waveforms can be amplitude and frequency modulated by applying external voltages at the VCA (Voltage-Controlled Amplitude) and the VCF (Voltage-Controlled Frequency) inputs. With these two inputs, the unit can easily produce amplitude modulated, frequency sweep, ASK (Amplitude-Shift Keying), or FSK (Frequency-Shift Keying) signal.Output frequency is adjustable from 0.5Hz to 500 KHz in 6 ranges. The DC offset of all waveforms can be adjusted between + and -10 Voltsby a front panel adjustment.
Specification:-
  • Frequency Range - 0.5Hz to 500 KHz (6 Ranges)
  • Wave Forms - Sine, Triangle & Square
  • Amplitude - Not over 20Vpp open circuit, Not over 10Vpp into 50 ohm.
  • Attenuation - 1/100
  • Frequency Accuracy - ±5% of full scale
  • DC Offset - Variable +10 to -10V open circuit,+5 to -5V into to ohm.
  • Sine Wave Distortion - 1% typical at 1 KHz.
  • Square Wave - Rise time 500ms typical.
  • VCF - Liner frequency sweep for controlVoltage from -2 to +2, input impedance 10K ohm.
  • VCA - Linear amplitude modulation approx. 10 to 1 variations for sine and triangle wave output,impedance 10K ohm.


Micro Controller Trainer Model
IPC-8605-MC
SPECIFICATION:
Model: IPC-8605-MC is user friendly Programmer and trainer base on 89c51 / 89s52 microcontroller. The system consists of,
SPECIFICATIONS:-
  • IR Transmitter
  • Built in in-Circuit Programming
  • IR Receiver
  • 4 Nos. Seven segment Display
  • ADC Interfacing
  • Serial Communication port
  • Liquid crystal Display
  • 10 pins Interface Data Connector 2Nos.
  • EEPROM 24CXX
  • Real Time clock DS 1307
  • Temperature sensor LM 35
  • 16 LED Displays
  • Key Pad Matrix
  • Solder Less bread board
  • Built in Power supply +5 VDC, ±12 Volt DC
  • Operate on 220 Volts 50 Hz AC
  • User Manual.
  • Software CD.
  • Connecting Leads.
Trainer is capable of performing different exercises on board.
  • Study of Single Bit Port Programming.
  • Study of Byte Writing.
  • Study of BIT Rotation.
  • Study of Arithmetic Instruction.
  • Study of Logic Instruction.
  • Study of LCD Interface.
  • Study of Serial Communication.
  • Study of Seven Segment Drive.
  • Study of Key Pad Interface.
  • Study of Traffic Light Signal


MICROPROCESSOR TRAINER MODEL
IPC-8603
SPECIFICATION:
SPECIFICATION: Based on Intel 8086/8088 CPU operating at 220V/50Hz. 8086 Processor can be replaced by 8088 processor. Onboard sockets provided to facilitate the use of 8087 Co-processor & 8089 I/O processor. 16K bytes of RAM available to user using 6264. 16K bytes of EPROM loaded with powerful monitor program (2764/27128). Total on board memory capacity of 128K bytes of RAM & 12K bytes of EPROM.
Battery back up provided for RAM area. 72 I/O line through 3 nos. of 8255. 16 bit timer / counter through 8253. RS-232 for CRT terminal through 8251. Baud rate selection through DIP switches from 110-19 baud. Provision for EPROM programmer for 2732/27256 with 28 pin ZIF with facility to program verify, list & blank check for even odd & continuous bytes. 28 Keys hexadecimal keyboard and eight seven segment display. Resident mode. Serial mode. POWERFUL SOFTWARE COMMAND LIKE GO, EXAMINE/MODIFY, REGISTER, SINGLE STEPPING, BLOCK MOVE, FILL, INSERT, DELETE, INPUT BYTE & WORD. Facility for uploading control signals, are buffered and available at the FRC connector. Power supply requirements: +5V/1.6A, +12V/250mA, +21V/24V. User manual, cables, connectors. Optional: A/D converter, D/A converter.


OPERATIONAL AMPLIFIER MODEL IPC
IPC-105-OP
SPECIFICATION:
This trainer covers the following subject with experiments ELT-214, ELT-243
SPECIFICATION :
  • -Operating Voltage 220-230Volts 50Hz -Variable 10K
  • -Fixed DC output Power Supply -Variable 50K
  • -DC ±5 Volts -Variable 100K
  • -DC ±12 Volts -Digital Multi meter
  • -Function Generator (Sine, Square, Triangle) -Frequency Counter
EXPERIMENTS:
  • Op-Amp characteristics Summing Amplifiers
  • The Differential Amplifier Measuring Amplifier
  • Inverting Amplifiers Responses
  • Non inverting Amplifiers Comparators
  • Amplifier Band width& Roll Off Rates Op-Amp Voltage
  • Op-Amp Slew Rates Followers
  • The Discrete Tuned Amplifier Op-Amp Feed Back


PROGRAMMABLE LOGIC CONTROLLER TRAINER MODEL
- IPC-14-FXIS U (Universal)
SPECIFICATION:
This trainer covers the following topics: Relays vs. programmable logic controller, how PLC functions, ladder diagram, ladder logic applications, program basis, programming the PLC, Editing program mistakes, series & parallel logics, Timer circuits, Counters, Sequencer circuits, Master control, Start/Reset, Shift register, Special scan timer logic circuit, High speed counter, Audio cassette program loading & down loading.
TECHNICAL SPECIFICATION: Power 230V 50Hz Approx.35w DC Supplies +5V,.08A A.10 mV Ripple, 3.5 regulation, with no load on ±15VAC, 0.8A each load on +5supply (1A each at ±10V), LED power supply indicator (3), 5VAC, 0.1A (20 primary 230V 50H, power supplies are short circuit protected, power supply terminal for measuring voltages. 15 pin Winchester socket provided for connection , accessory panel bas.
PLC SPECIFICATION: Operating temperature: 0-60 degrees celsius (32-140F) available user power (DC) 24Volts @ 0.1A max. battery life:- 25 years, Memory size 16-bit words,700 words COMS EPROM. Scan Rate:12ms for 250 words.40 ms. For 700 words I/O points, Digital 8 inputs, 6 outputs, analog 4input, 2outputs.


PROJECT BOARD TRAINER MODEL
IPC-72-PB
SPECIFICATION:
  • Fixed + 5 Volts DC.
  • Variable +20 Volts DC
  • Variable -20 Volts DC
  • Fuse Protection
  • Bread Board size 7" x 6.75"
  • Operate on 220 Volts, 50Hz
  • Size Of Trainer 12" x 14"
RELAY LOGIC TRAINER
IPC-5500-RLT
     
SPECIFICATION :
 FIXED 24VDC POWER SUPPLY.
 24VDC REALYS 6NOS.
 24VCD INDICATION LAMPS 4NOS.
 PUSH SWITCHES 4NOS.
 24VDC BUZZER 
 24VDC FAN
LIST OF EXPERIMENTS:
 INTRODUCTION TO LOGIC SYMBOLS.
 TO PERFROM  AND / NAND FUNCTIONS BY USING RELAYS.
 TO PERFROM  OR / NOR FUNCTIONS BY USING REALYS.
 COMBINED OR / NOR CIRCUITS.
 LOGIC CIRCUITS FROM A TRUTH TABLE.
 EXOR CIRCUITS.
 IDENTITY CIRCUITS.
 RELAY DECORDER.
 COUNTER USING RELAYS.
 ADDER CIRCUITS.